The Le Chatelier appratus is used to determine?
Anonymous Quiz
13%
Compressive strength of cement
9%
fineness of cement
15%
setting time of cement
44%
soundness of cement
4%
None of the above
16%
All of the Above
October 3, 2021
The setting time of cement is determined using
Anonymous Quiz
25%
Le Chatelier apparatus
10%
Briquette testing apparatus
56%
Vicat apparatus
10%
Casagrande's apparatus
October 3, 2021
As per Indian standards for bricks, minimum acceptable compressive strength of any class of burnt clay bricks in dry state
Anonymous Quiz
32%
10.0 MPa
13%
0.75 MPa
23%
5.0 MPa
32%
3.5 MPa
October 4, 2021
A simply supported beam is subjected to a uniformity distributed load. Which one of the following statement is true?
Anonymous Quiz
17%
Maximum or minimum shear force occurs where the curvature is zero.
44%
Maximum or minimum bending moment occurs where the shear force is zero.
18%
Maximum or minimum bending moment occurs where the curvature is zero.
21%
Maximum bending moment and maximum shear force occur at the same section.
October 4, 2021
The values of partial safety factor for dead load and live load in limit state of collapse are
Anonymous Quiz
14%
1.5 and 1.1
32%
1.5 and 1.0
31%
1.0 and 1.5
23%
1.5 and 1.5
October 4, 2021
In the limit state of collapse, the values of partial safety factor for concrete and steel are
Anonymous Quiz
13%
1.67 and 0.87
58%
1.5 and 1.15
15%
1.15 and 1.5
13%
0.87 and 1.67
October 4, 2021
The maximum compressive strain in concrete in axial compression in limit state of collapse is
Anonymous Quiz
42%
0.0035
18%
0.0015
24%
0.0025
16%
0.002
October 5, 2021
Meridonal thrust in a sphere dome subjected to a concentrated load or uniformly distributed load, is always
Anonymous Quiz
21%
tensile
45%
compressive
23%
zero
10%
none of the above
October 5, 2021
Which type of wires have high tensile stength?
Anonymous Quiz
30%
Heat treated wires
39%
Plain cold drawn wires
23%
Plain hot drawn wires
9%
None of the above
October 5, 2021
Hope you like the questions that we are posting, if you have any suggestion or recommendation, leave a comment and we will make sure your all demand fulfills.
October 5, 2021
A culvert having a length less than 1 m is called
Anonymous Quiz
12%
Minor bridge
28%
Vent way
38%
Culvert
22%
Viaduct
October 5, 2021
The bridge having its floor supported at the top of the structure is known as
Anonymous Quiz
14%
Semi through bridge
53%
Deck bridge
20%
Through Bridge
13%
Submersible bridge
October 5, 2021
The bridge having its floor flush or a little above the bed of the stream which allows flood water always to pass over its super structure is called as
Anonymous Quiz
12%
Vent way
33%
Minor Bridge
31%
Cause way
24%
Viaduct
October 5, 2021
The bridge constructed to enable a road to pass under another land communication route is called an
Anonymous Quiz
28%
Under bridge
21%
Over bridge
34%
Subway
18%
Flyover
October 5, 2021
The bridge having its floor supported at the bottom of the main girders is called
Anonymous Quiz
30%
through bridge
41%
deck bridge
23%
semi through bridge
6%
none of these
October 6, 2021
The walls constructed on both sides of the abutments to retain the earth of the bridge approaches are known as
Anonymous Quiz
50%
Wing wall
13%
Piers
24%
Abutments
13%
Abutment pier
October 6, 2021
The drainage structutre provided to pass the abutments to retain the earth of the bridge approaches are known as
Anonymous Quiz
32%
Cause way
20%
Viaduct
25%
Vent way
24%
Aquaduct
October 6, 2021
Forwarded from GATE CIVIL ENGINEERING PREPARATION
October 6, 2021
The centre to centre distance between any two adjacent supports of a bridge is called
Anonymous Quiz
45%
Span
13%
Economic span
41%
Clear span
2%
None of these
October 7, 2021
The difference between the highest flood level and lowest point on the under side of the bridge super structure is known as
Anonymous Quiz
23%
Head room
23%
Water way
37%
Free board
17%
Clearance
October 7, 2021